I have a mapcase made of clear plastic (PVC I think). It has a roll top held shut with velcro. Both sides of the velcro were attached by some sort of welding process but one of them has completely come off. I've tried reattaching it with hot glue, which seemed OK at first, but didn't survive one use. I've tried pressing the plastic to the backing of the velcro with a heated tool, but despite the hot plastic smell there was no adhesion.

Not only is it my most waterproof mapcase, ideal for inkjet-printed maps in the rain, but it attaches to the handlebar bag of my bike. Replacements don't seem to be available, and it's perfect for riding to a hike, something I quite like to do. But with the velcro missing the maps simply fall out (it's at the bottom).

I don't want to sew through the plastic unless I absolutely have to: it will breach the waterproof section, and I don't appear to have anything that I could use to seal the holes.

damaged mapcase

On the left, a strip of velcro that's firmly attached; In the middle, the remains of the weld; on the right, the velcro that came off. The weld (which shows up as a white rectangle) is textured in the side that touched the velcro, and smooth on the other side, suggesting that any melting was very controlled, and possibly delivered through the velcro (which has an edge of just fabric).

  • I thgouht I had a picture here but I don't. I'll add one later.
    – Chris H
    Commented May 15, 2018 at 13:31
  • i don't know what temperature plastic has to be at to weld, but there's certainly a way to re-weld it. do you have a cheap soldering iron at hand with a tip you don't mind disposing of afterward? Commented May 15, 2018 at 18:40
  • @JonathanLandrum I haven't got a spare tip but I've got a rough old iron. I reckon it would get hot enough to go straight through the plastic and out the other side. I tried heating an old spanner in a gas flame and I think the issue it that it melts the surface it touches but not the surface the velcro touches.
    – Chris H
    Commented May 15, 2018 at 19:17
  • have you tried super glue? That would be my next attempt before sewing or further heating.
    – Nate W
    Commented May 15, 2018 at 22:48
  • @NateW no, because I've never had much luck with superglue on flexible materials.
    – Chris H
    Commented May 16, 2018 at 5:52

1 Answer 1


Like you said, there are probably a hundred classes of adhesives available today, each one totally unsuitable for the things the others excel at. So we need to take a diagnostic approach here.

You need flexible, which rules out many types of adhesives, including CA (Super glue), epoxies and resins, polyurethanes (Gorilla glue and I think hot glue is in this category), and many others.

You also have one of your surfaces being non-porous. This rules out PVA (white glue) and Aliphatic (wood glue) and a few others which rely on "creeping" into the surfaces before curing to acheive full adhesion.

So what's left? To be honest, not much, but I still haven't ruled out rubber based adhesives. This class includes rubber cement, contact cement, the Liquid Nails brand, and their relatives. Of these, I suggest some type of contact cement. Go to your favorite hardware store and read a few labels, I expect you will find one that matches your criteria. This article may help a bit as well.

Note the usage directions: Apply the cement to both surfaces, allow to dry for a short time while still separated, then place the surfaces together with pressure.

I am perhaps only 70/30 confident that contact cement will work for you. But I am 95/5 confident most other things will not work. Good luck, and tell us how this turns out.

  • FWIW, I also did not rule out cellulose (Duco cement), which might be an option if the rubber based is not.
    – cobaltduck
    Commented May 17, 2018 at 14:50
  • I've got something drying at the moment with wetsuit repair glue (my contact cement had dried up and Neoprene Queen has worked well before) so we'll see. The solvents in some other glues did funny things to the plastic when I tested last night.
    – Chris H
    Commented May 17, 2018 at 15:00
  • @ChrisH - How did things turn out?
    – cobaltduck
    Commented May 21, 2018 at 21:32
  • The wetsuit glue seemed to work. That's a sort of contact cement. I didn't have enough to finish the job, so stuck the corners down with seam sealant (my tube of which is described as being good for gluing waterproof kit) it attacked the plastic but stuck everything together. It seems like it's going to work but the real test will be when I actually use it
    – Chris H
    Commented May 22, 2018 at 6:34

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.