So roughly a month ago my other half and I brought ourselves each a SOT plastic kayak, we've been out on the water for maybe 2 hours total paddling time, but mine filled up with water.

We found a hole, approx. 1cm by 0.4cm, in the seam of the plastic in one of the two rear drainage holes, too small to get your hand down easily. I am currently talking to the manufacturer about a replacement.

However this has lead me to wonder (outside of warranty) how would I go about repairing a hole in a plastic kayak? Varied sized holes, and temporary and permanent fixes, I understand will vary.

  • 3
    Duct tape...??? More helpful advice is probably here
    – nivag
    Commented Aug 14, 2014 at 8:20

5 Answers 5


The main issue with repairing plastic hulls is that is that most adhesives don't bond very well to the plastic. For temporary repairs duct tape is the way to go. Its quite adhesive and waterproof. If the hole is too big use the duct tape to secure something else waterproof (e.g plyboard or plastic) in place. If possible try and do both inside and out.

If you want to do a permanent repair there seem to be two options:

Repair in a similar way to fiberglass. I.e. Sand the surrounding area and apply a fiberglass patch and epoxy. The one significant difference is that the area around the hole should be flame treated before applying the patch by lightly heating with a propane torch or similar. This helps the epoxy bond to the surface. Be careful not to burn your boat though.

The alternative, more conventional, way is to melt/weld more plastic into the hole. I suspect this is what a professional would do if you asked them to do the repair. Here's another good article on it. For smallish holes you want to get some polyethylene welding rod (presuming the boat is polyethylene) for large holes you need to get a patch. The basic idea is to melt the rod into the hole using a hot air gun or hot metal. As you've melted two of the same material together this repair should be very strong.

Disclaimer: I'm mainly a dinghy sailor so haven't actually repaired any plastic hulls. This is just based on my general understanding of boat repair and reading the internet.

  • 1
    epoxy does not bend in the same way as plastic to does not work over a large area. Commented Aug 14, 2014 at 15:03
  • If using epoxy, it's worth paying extra for elasticised variants. I've used G/Flex 650 with some success. Commented Mar 11, 2019 at 15:07

I've seen people use a soldering iron and a piece kf abs plastic to repair tears in the hull but the best answer is short and simple to use for small holes: epoxy putty.

just follow instructions on the packaging, fill the hole with a small (few mm) overlap inside and out and if you want sand down when hard and paint.

  • Would you avoid using a bit of fiberglass for good measure? Commented Dec 9, 2014 at 0:38
  • It won't hurt for sure, it just depends on how much time you have to fix it.
    – HTDutchy
    Commented Jan 30, 2015 at 11:04
  • It just seems likely the epoxy without the fiberglass would crack, is all I was thinking. ;-) Commented Jan 30, 2015 at 21:03

It's quite common to melt in some plastic - but be sure to get the same as the boat is made of. Most are PE so try to get some of that -- avoid ABS. Kits are available (random web example). The general recommendation among people I know who've done this is to use a hot air gun rather than a naked flame. You can also overfill a touch and smooth down later. The repair will be pretty good for flat-water use, but will always be a weak spot to be wary of in significant white water and to a lesser extent surf. As you've got SOTs I'm guessing/hoping you're not doing much if any river-running so you should be fine. Be sure to get all the water out first though, you don't want to trap it in there, and make sure the surface is clean before repairing it (e.g. of salt if you've been in the sea).


For from upto small leak holes to upto coin-sized holes, You can possibly use a Duct tape on the both sides. One more thing to add between the Duct Tape's point of contact is a filler like Some local Epoxy Compound product, or worst case a Chewing Gum (Chewed one :D).

For a crack, you might just get it fixed by a Duct Tape.

  • Duct tape as a permanent fix or a temporary fix?
    – Aravona
    Commented Aug 14, 2014 at 9:27
  • @aravona: Its more likely to be a temporary fix. But working out well for me so far. I'd say, so far so good.
    – WedaPashi
    Commented Aug 14, 2014 at 9:43
  • 3
    In addition being more likely to be damaged again than the rest of the hull in the future, Ducttape's adhesive tends to dry out and come loose after a few months. Commented Aug 14, 2014 at 14:54
  • A downvote? May be the downvoter care to explain?
    – WedaPashi
    Commented Sep 7, 2014 at 3:13
  • 1
    @Niall: 3 Minutes? Just that? LOL. I have seen a Kayak that endured an entire weekend with a duct tap fix. You might want to consider trying a different brand of duct tape.
    – WedaPashi
    Commented Aug 20, 2015 at 4:36

Shoe glue to fill the hole"let it dry". Then JB weld spread over a area 20 times the size of the hole. Or shoe glue then aluminum sheet, 4 bolts and cover with jb weld on both sides.

  • 2
    Hi Spencer. Welcome to The Great Outdoors! Consider adding a bit more detail to your answer to make it as useful as possible. Possibly add links showing the process. It also seems like you are recommending multiple options so consider spacing them out into different paragraphs or groups of bullets. That way a reader can follow a bit more step-by-step for the different methods.
    – noah
    Commented Jul 24, 2019 at 23:19

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.