Starting a fire can sometimes be hard enough when it's dry, let alone when it's tipping it down. But when it is, what steps should you follow to try to ensure the fire gets going successfully?

I'm talking about the process of gathering firewood when it may be damp, to start a fire in the rain - assuming basic things like matches are available but not much else.

  • 2
    your question is pretty open ended. Are you asking how you start a fire from firewood gathered in the forest during the rain? wood gathered before rain but needing to light it during rain? a stove fire that you need to get lit in the rain and keep it running? all of these would require different tactics.
    – Justin C
    Feb 15, 2012 at 17:41
  • @JustinC Good point, I've clarified the question.
    – berry120
    Feb 15, 2012 at 23:02

3 Answers 3


When building a fire in any weather condition you need some kind of starter. If you are expecting to experience wet conditions a great planning step is to store some starter in a waterproof location. If you don't have any household material, then gathering kindling and storing that will work. When backpacking I keep a small water-proof cylinder with a lighter, 2-3 strike anywhere matches, and some tightly rolled newspaper.

You'll also need larger pieces of wood to sustain the fire. Eventually your fire will be able to handle wood that is slightly damp, but you'll need a few decent pieces of dry wood to build up a base of hot coals that can then be used to help dry wood later. The best way to accomplish this in wet conditions is to look for naturally piled up wood or big thickets. Underneath a fallen tree can be a great place to find some medium sized sticks that have been shielded from the rain.

As for starting the fire, you will most likely need some kind of cover. The amount of cover depends on how bad the rain is. At a minimum you'll need good cover when starting the fire, and depending on conditions you may be able to fully uncover your fire once it is started. This is where all the big warnings need to be posted though! The cover over the fire could itself catch fire, creating a dangerous situation. The cover could block fresh air, which obviously is dangerous around a fire, not to mention bad for the fire as well. The few times that I have needed to start a fire in a very light rain, I simply used by body as cover for the kindling, and once that was going an occasional drop of rain wasn't a problem, never tried in a heavier rain though.

The last item I would mention is placement. Especially if you are quickly getting your fire going as rain starts, make sure to pick a place that will not get washed out if the rain intensifies. If you are using a fire pit this shouldn't be a concern.


As with all fires, you need more tinder and kindling than you think. In dry conditions I once heard the advice of "get as much as you think you need, then double it". In wet conditions, I'd suggest you triple/quadruple the amount of kindling and triple the tinder.

Specifically, take the tinder and get it out of the rain as soon in your firewood gathering process as possible. Give the tinder as much time as possible to dry out a bit.

Build the fire, but put some sort of tarp or cover over top of it until it is caught. I'd recommend getting 2 friends to hold a poncho horizontal at shoulder level, and then take a few side-steps once the fire has started. If you are alone, tie the tarp overhead and get it out of the way as soon as you have strong flames on the kindling.

Once the fire is lit, set up a small pallet with some of your fuel/kindling to get and keep the wood you are planning to burn off of the ground. also keep it as near the fire as you can safely. The heat will help to dry out the wood before you put it on the fire (but some of it will be wet).

  • "Get as much as you think you need, then get more" Indeed. As an added bonus, if you do manage to get a good fire going without needing all of it, you have some left for the next fire you start. This could be especially important in the wet conditions here, as the starter materials are not only a jump-start on the next fire, but they can also be drying out in the meantime if needed. Double-win.
    – Loduwijk
    Apr 28, 2017 at 20:39


Back "in the day" we would always look for birch bark (as it burns when wet) and/or toss a little white gas from the stove onto the fire.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.